Airmar

Airmar

Airmar 10-Conductor In-Line Cable Splice - IP67 [D00342H]

10-Conductor In-Line Cable Splice - IP67Airmar CHIRP transducers are made with cables ending in a bare wire connection. Some sounders have internal terminal blocks to which these bare wires can be...

Airmar

Airmar 11-Pin Low-Frequency Mix Match Cable f/Raymarine [MMC-11R-LDB]

11-Pin Low-Frequency Mix & Match Cable for RaymarineSome CHIRP transducers are now made as Mix and Match models. These versions have a common base transducer with an attached 9-meter cable, plus...

Airmar

Airmar 117WR-1 Crows Foot Transducer Wrench [117WR-1]

117WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut...

Airmar

Airmar 117WR-2 Transducer Hull Nut Wrench [117WR-2]

117WR-2 Transducer Hull Nut WrenchA single-handed wrench to tighten the hull nut on 2" bronze and stainless steel housings.You can use wrench 117WR-4 to brace the housing when using this wrench.For...

Airmar

Airmar 117WR-3 Double Handle Transducer Wrench [117WR-3]

117WR-3 Double Handle Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut...

Airmar

Airmar 117WR-4 Transducer Housing Wrench [117WR-4]

117WR-4 Transducer Housing WrenchA single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the side of the housing to facilitate tightening of the hull nut. For 2"...

Airmar

Airmar 164WR-1 Crows Foot Transducer Wrench [164WR-1]

164WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut...

Airmar

Airmar 164WR-2 Transducer Hull Nut Wrench [164WR-2]

164WR-2 Transducer Hull Nut WrenchA single-handed wrench to tighten the hull nut on B164, SS164 and SS264 housings.You can use wrench 164WR-4 to brace the housing when using this wrench.For use...

Airmar

Airmar 164WR-3 Double Handle Transducer Wrench [164WR-3]

164WR-3 Double Handle Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut...

Airmar

Airmar 175WR-4 Transducer Housing Wrench [175WR-4]

175WR-4 Transducer Housing WrenchA single-handed wrench that holds the main thru-hull housing via the 'wrench flats' on the top of the housing to facilitate tightening of the hull nut. Use wrench...

Airmar

Airmar 599 Low/High Frequency - In-Hull Chirp Transducer w/o Connector [R599C-LH]

Low/High Frequency - In-Hull Chirp Transducer without ConnectorRely on Airmar's new broadband transducers for your ultimate fishing mission. Whether you're a commercial fisherman, charter captain,...

Airmar

Airmar 60WR-1 Crows Foot Transducer Wrench [60WR-1]

60WR-1 Crows Foot Transducer WrenchTransducer wrenches are available for all bronze low profile transducers. They are used to facilitate holding of the transducer and tightening of the hull nut...